My Laptop Screen Has Yellowish Blotches On A White Background
Yellowish blotches on white are often caused by pressure on the panel, for example from the keyboard touching the screen when closed, or by heat…

Hardware Repair Educator at Gamepad Tester
Shows players how to use a test result to find and fix a fault themselves.
Thiago teaches controller repair. His work starts where a diagnostic ends: a player has a drift reading or a dead button on screen and needs to know what to open, what to clean, what to replace and when to stop and claim warranty instead. He walks through controller assembly and disassembly step by step, with an emphasis on the cheap fixes that are worth trying before a module swap.
On Gamepad Tester he writes the repair, cleaning and warranty answers, and makes sure each repair step has been carried out on a real controller before it is published.
Yellowish blotches on white are often caused by pressure on the panel, for example from the keyboard touching the screen when closed, or by heat…
Do not buy a generic hobby motor. The left and right motors differ in size and weight, so buy a replacement listed for your exact controller and…
The speaker is almost certainly not seated back into its acoustic pocket, or its gasket is pinched. A speaker sitting proud or leaking air distorts…
Repair it. All three of your faults are replaceable parts, together they come to a fraction of a new controller, and none of them need soldering…
Sand in the trigger pivot, and yes you can clean it, but do it properly rather than flushing from outside. Sand is abrasive, so every pull is…
Since AA batteries work, the controller is fine. Check the cable carries power, the pack sits firmly and the contacts are clean. If a known-good…
Reasonable to think about, and there are specific checks. The main question is whether the dock charges through the controller's own circuit or…
A reading pinned at 1.00 or -1.00 is not normal drift; it usually means a broken sensor track, a cracked solder joint or a loose connection on that…
Yes. DualSense sticks are soldered, so it is a desoldering job rather than plug and play, but drop-in Hall effect and TMR modules exist for it…
It is a manageable job with patience: open the shell, disconnect the battery connector carefully, swap the battery and reassemble without damaging…
The Elite Series 2 has adjustable stick tension using the small tool included in the box. Remove the stick tops, insert the tool and turn it to…
You have almost certainly left a screw under-tightened or a clip unseated, and possibly cross-threaded one. Nothing is damaged. Reopen it, seat the…
Entirely cleanable, but it needs opening. Sugar residue has to be dissolved and removed, not wiped at from outside, and leaving it will corrode the…
Quite possibly. Bleed comes from uneven pressure on the panel, and over-tightened VESA screws or a stressed mount can twist the frame. Loosen the…
Repairable, and it is a cheap part. The Create and Options buttons sit on a small flex membrane that is easy to reach once the shell is open, and at…
Leaving it on the charger overnight is fine; the controller stops charging when full. Heat and running the battery completely flat matter more for…
Grips do not add meaningful leverage and the drift claim is overstated. The real risk is trapped debris underneath them, which is abrasive. Keep…
If the trigger test still shows a smooth 0 to 1, the sensor is fine. Squeaks and grit come from dust or worn plastic on the trigger pivot or the…
Record a counted sequence on video with the test on screen. Twenty presses with a visible miss rate is far harder to dismiss than a demonstration…
A loose R2 resting at 0.12 is almost always a broken or unseated return spring, one of the most common DualShock 4 faults. The spring is a cheap…
Yes. A knock can shift the stick module, crack a solder joint or move the potentiometer slightly, giving an instant offset. It rarely fixes itself…
Almost certainly the motor is no longer seated properly in its pocket. An actuator held loosely, or with its wire routed under it, transmits far…
The port's solder joints have cracked from cable flexing, which is the classic micro USB failure. It is not dangerous but it will get worse, and a…
Stop charging it and do not use it on the cable. A burning smell means something is overheating, and with a lithium cell and children in the house…
An L3 that registers about half the time is usually a worn or dirty tactile switch under the stick. Cleaning sometimes helps, but the lasting fix is…
Each answer is written by the specialist who owns that part of the hardware, tested on a real controller, and checked by a second team member. How we verify answers