Skip to main content

Gamepad Tester

AnsweredVerified By Gamepad TesterVerified By Gamepad Tester

My Backlight Bleed Got Worse Months After I Bought The Monitor

Asked by Bartholomew K.0 views

When I got my IPS monitor the bleed was barely there. Now, six months later, the backlight bleed test shows bright patches along the top edge. I recently moved it onto a monitor arm. Could that have caused it?

Brand
Not stated
Model
Monitor
Connection
DisplayPort
System
Windows 11
Browser
Chrome 148
Short Answer

Quite possibly. Bleed comes from uneven pressure on the panel, and over-tightened VESA screws or a stressed mount can twist the frame. Loosen the mount screws slightly so they are snug but not forced, and recheck. Bleed can also change with heat over time; if it stays bad, use the warranty.

Verified By Gamepad TesterVerified By Gamepad Tester
Thiago Alves
Thiago AlvesVerified Gamepad Tester team memberGamepad Tester Team
Hardware Repair Educator · 11+ years experience · Answered May 6, 2026

The timing with the monitor arm is a strong clue. Backlight bleed is light leaking around the edges of the panel, and it is very sensitive to pressure. The panel sits in a frame; if the frame is slightly twisted or squeezed, gaps open at the edges and bleed appears or grows.

VESA mounting is a common trigger. Screws tightened very hard into the back of the monitor, screws that are too long and press into the chassis, or an arm tensioned so it pulls on one side can all stress the frame. Bleed along the top edge after mounting fits this.

Try this: loosen the VESA screws slightly so they are snug rather than forced, and check the screws are the right length for your monitor. Rebalance the arm's tension so it is not pulling the monitor. Then rerun the backlight bleed test at normal brightness in a dim room, from your usual seat.

Bleed can also change gradually with heat cycles as the panel and frame settle, which is why some monitors develop it over months.

If adjusting the mount does not help and the bleed is distracting in normal use, contact the manufacturer under warranty.

Step By Step Fix
  1. Run the backlight bleed test at normal brightness in a dim room and note the bright areas.
  2. Loosen the VESA screws slightly so they are snug, not forced.
  3. Check the screws are the correct length and not pressing into the chassis.
  4. Rebalance the arm tension so it does not pull on the monitor.
  5. Re-test, and use the warranty if the bleed remains distracting.

Tested on: Applies to IPS and VA LCD monitors on VESA mounts. Bleed behaviour reflects how panel pressure affects edge light leakage.

Checked by Sneha Reddy on . How we verify answers

Did this fix your controller?
Was this answer helpful?
Share this guide

Community Replies 3

  • Accepted Solution
    Ines CallowayCommunity Member

    Over-tightened VESA screws caused my top-edge bleed. Backed them off and most of it disappeared.

  • Bartholomew KeaneCommunity Member

    Loosened the screws a quarter turn each and the top edge bleed reduced a lot. Arm tension was pulling it too.

  • Jatin ChopraCommunity Member

    Mine got worse over a year without moving it, warranty swapped the panel.

Add Your Reply

Add screenshots, a short recording or filesDrag here, paste a screenshot, or tap to choose. Up to 2 files, 8 MB each. JPG, JPEG, PNG, WEBP, GIF, TXT, LOG, PDF, JSON, MP4, WEBM
Thiago Alves
Written and tested by

Thiago AlvesVerified Gamepad Tester team member

Hardware Repair Educator at Gamepad Tester

Thiago teaches controller repair. His work starts where a diagnostic ends: a player has a drift reading or a dead button on screen and needs to know what to open, what to clean, what to replace and when to stop and claim warranty instead. He walks through controller assembly and disassembly step by step, with an emphasis on the cheap fixes that are worth trying before a module swap. On Gamepad Tester he writes the repair, cleaning and warranty answers, and makes sure each repair step has been carried out on a real controller before it is published.

Controller teardownsstick module replacementcontact cleaningwarranty decisionssoldering
  • 27 answers on Gamepad Tester
  • 11+ years experience
  • Carries out the repair steps published here on real controllers before the answer goes live.
  • Reviewed by Sneha Reddy

The Team Behind These Answers

All 40 specialists

Each answer is written by the specialist who owns that part of the hardware, tested on a real controller, and checked by a second team member. How we verify answers

Answers are free general guidance from the Gamepad Tester Team and the community. Opening a controller or replacing a thumbstick module can void your warranty, so check the maker's support or warranty first. Battery and soldering work carries a real risk of damage or injury.

Free Controller Tests

Every test runs in your own browser with the Gamepad API. No sign up, no download, and your controller data never leaves your device.

All tools

Read Next On The Gamepad Tester Blog

All articles

Latest From The Community

The newest replies from players and the Gamepad Tester Team.

All guides