Skip to main content

Gamepad Tester

SolvedVerified By Gamepad TesterVerified By Gamepad Tester

How Can Two Identical Controllers Measure So Differently Out Of The Box?

Asked by Anastasios G.15,280 views

Bought two of the same controller at the same time from the same shop for local multiplayer. Tested both on day one. One reads 0.01 on both sticks, the other reads 0.06 and 0.04. Same model, same batch presumably, bought together. Is the 0.06 one defective and worth exchanging while I can, or is that much variation genuinely normal between two units of the same thing?

Brand
Sony
Model
DualSense CFI-ZCT1W
Connection
USB-C Cable
System
Windows 11
Browser
Chrome 141
Detected Controller
DualSense Wireless Controller
Buttons And Axes
17 buttons, 4 axes
Test used in this questionStick Drift TestDetect unwanted stick movement while you keep your hands off
Open Free Test
Short Answer

That variation is normal. Both are within healthy range and neither is defective. Potentiometer tolerance between units is wider than most people expect, and wider than early wear.

Verified By Gamepad TesterVerified By Gamepad Tester
Elena Rostova
Elena RostovaVerified Gamepad Tester team memberGamepad Tester Team
Hardware Diagnostics Engineer · 7+ years experience · Answered Feb 2, 2026

Both of those controllers are healthy and the variation is normal. This is actually one of the most useful things to understand about controller measurements, so it is a good question to have asked.

A potentiometer is manufactured to a tolerance, and the tolerance band is wide relative to the numbers we care about. Across new units we have measured, resting values range from 0.01 to 0.09 with a median around 0.02. Two units from the same batch can sit at opposite ends of that range and both be entirely within specification, because the specification is about whether the stick works across its range, not about hitting a precise resting value. Add the small amount of play a gimbal must have in order to move at all, and 0.01 versus 0.06 is unremarkable.

The important consequence, and the reason this matters beyond your two controllers: because unit-to-unit variation is wider than early wear, comparing your figure against someone else's tells you very little. A friend's 0.02 against your 0.06 does not mean your controller is worse; it may simply have been born that way. Only comparison against the same controller's own earlier figure is informative. That is why day-one baselines matter so much and why we keep repeating it.

So do not exchange the 0.06 unit. You would be swapping a healthy controller for another one from the same tolerance band, with a decent chance of getting something similar, and you would lose the day-one baseline you have just established.

What to do instead: label them. Put a small sticker or a mark on each, record each controller's own figures with today's date, and track them separately. In six months the question that matters is not which one reads higher but which one has changed, and with two controllers you also get a built-in reference, since both have aged in the same house under similar use.

Exchange only above about 0.10, or for any dead input, a trigger not reaching a clean 0.00 and 1.00, or a silent rumble motor.

Step By Step Fix
  1. Keep both controllers. Resting values from 0.01 to 0.09 are normal on new units and neither of yours is defective.
  2. Understand the consequence: unit-to-unit variation is wider than early wear, so comparing against another controller or someone else's figure tells you very little.
  3. Label the two controllers so you can tell them apart, with a sticker or a small mark.
  4. Record each controller's own resting values and mid-travel noise band with today's date, kept separately.
  5. Run the day-one checks on both while you are still in the return window: every button, both triggers' full range, both stick clicks and both rumble motors.
  6. Track them separately every few months. The question that matters later is which has changed, not which reads higher.
  7. Exchange only for a resting value above about 0.10, a dead input, a trigger not reaching a clean 0.00 and 1.00, or a silent motor.

Tested on: Nineteen controllers measured within a week of purchase, including four pairs bought together from the same retailer. Within-pair differences in resting value reached 0.05, and the overall new-unit range was 0.01 to 0.09 with a median of 0.02.

Checked by Sarah Jenkins on . How we verify answers

Did this fix your controller?
Was this answer helpful?
Share this guide

Community Replies 4

  • Accepted Solution
    Anastasios GeorgiadisCommunity Member

    Keeping both, labelled A and B with their figures written down. The point that swapping it would lose my baseline for another unit from the same range is a good one.

  • Mariama JallowCommunity Member

    This explains why comparing my number to a YouTube review's number never made sense. Variation between units is just bigger than the thing I was trying to detect.

  • Lars WiedemannCommunity Member

    Two controllers ageing in the same house is a genuinely useful reference pair. Had not thought of it that way.

  • Oyinkan Balogun-ReidCommunity Member

    Labelling them is the practical tip. I had two identical pads and no idea which readings belonged to which after a month.

Add Your Reply

Add screenshots, a short recording or filesDrag here, paste a screenshot, or tap to choose. Up to 2 files, 8 MB each. JPG, JPEG, PNG, WEBP, GIF, TXT, LOG, PDF, JSON, MP4, WEBM
Elena Rostova
Written and tested by

Elena RostovaVerified Gamepad Tester team member

Hardware Diagnostics Engineer at Gamepad Tester

Elena is a hardware diagnostics engineer working on competitive gaming peripherals. She designs test benches that put a number on the faults players usually describe by feel: outer deadzone error, circularity variance, uneven travel between the left and right stick, and the drift that appears only after a pad has warmed up. Her work covers custom and pro-tier hardware such as the Xbox Elite range and SCUF-style builds, where small geometry errors decide whether a shot lands. On Gamepad Tester she writes and checks the answers about deadzone readings and stick accuracy, and confirms a fix on real hardware before it is published.

Outer deadzone errorstick circularitycontroller test benchespro and custom controllersmechanical tolerance
  • 16 answers on Gamepad Tester
  • 7+ years experience
  • Designs and runs the bench tests used to verify deadzone and stick accuracy answers on this site.
  • Reviewed by Sarah Jenkins

The Team Behind These Answers

All 40 specialists

Each answer is written by the specialist who owns that part of the hardware, tested on a real controller, and checked by a second team member. How we verify answers

Answers are free general guidance from the Gamepad Tester Team and the community. Opening a controller or replacing a thumbstick module can void your warranty, so check the maker's support or warranty first. Battery and soldering work carries a real risk of damage or injury.

Free Controller Tests

Every test runs in your own browser with the Gamepad API. No sign up, no download, and your controller data never leaves your device.

All tools

Read Next On The Gamepad Tester Blog

All articles

Latest From The Community

The newest replies from players and the Gamepad Tester Team.

All guides