Skip to main content

Gamepad Tester

SolvedVerified By Gamepad TesterVerified By Gamepad Tester

I Have To Re-Pair My Controller Every Time I Restart My PC

Asked by Agnieszka Z.20,360 views

The pairing never survives a restart. Shut down, boot up, and the controller is gone from Bluetooth and I have to pair it again from scratch, hold the buttons, add device, the whole thing. Every single time. It works perfectly once paired, no dropouts, good range on your Bluetooth pairing range test, so it is purely the pairing not persisting. It is a small thing but doing it daily is wearing thin.

Brand
Sony
Model
DualSense CFI-ZCT1W
Connection
Bluetooth
System
Windows 11
Browser
Chrome 141
Detected Controller
DualSense Wireless Controller
Buttons And Axes
17 buttons, 4 axes
Short Answer

The pairing key is not being stored, usually because the Bluetooth adapter is being reset at shutdown or its driver is reinstalling each boot. Disable fast startup and adapter power saving first.

Verified By Gamepad TesterVerified By Gamepad Tester
Liam Davies
Liam DaviesVerified Gamepad Tester team memberGamepad Tester Team
Bluetooth And Wireless Test Engineer · 11+ years experience · Answered May 16, 2026

A pairing that works perfectly but never survives a reboot is a storage problem rather than a radio problem, and your clean range results confirm the radio side is fine.

When two Bluetooth devices pair, each stores a link key. On a PC that key lives with the adapter's configuration. If the key is lost at shutdown, the controller still holds its half, the PC does not, and you have to pair from scratch. Three things commonly cause that.

First, the adapter being reset or reinitialised at boot. Windows 11's fast startup complicates this, because a hybrid shutdown restores a saved state rather than initialising cleanly, and on some adapters the stored pairing does not survive the round trip. Disabling fast startup is the first thing to try and it resolves a good share of these.

Second, adapter power management. If Windows is allowed to power the adapter down, some drivers drop their stored pairings when the device re-initialises. The setting is a checkbox in Device Manager under the adapter's power management tab.

Third, a driver that reinstalls each boot, which happens when a generic driver and a vendor driver are fighting, or after a partial driver update. If Device Manager shows the adapter with a different name or a warning after each reboot, this is your cause, and a clean uninstall followed by the vendor's own driver fixes it.

One genuinely useful alternative while you work through this: the controller holds pairings for multiple devices and reconnects to whichever it last used, so if the PC side keeps forgetting, the cable is a zero-effort daily option and gives you lower latency anyway. Not a fix, but it stops the daily annoyance while you sort the driver.

If none of the three works, a cheap USB Bluetooth dongle with its own driver sidesteps a motherboard adapter that will not store keys properly.

Step By Step Fix
  1. Disable fast startup in Windows power settings, then shut down fully and boot. A hybrid shutdown restores a saved adapter state that can lose stored pairings.
  2. Open Device Manager, find the Bluetooth adapter, open Properties then Power Management, and untick the option allowing Windows to power it down.
  3. Reboot and check whether the pairing survives. These two settings resolve most cases.
  4. Watch Device Manager across a reboot. If the adapter appears with a different name or a warning each time, its driver is reinstalling and that is your cause.
  5. If the driver is reinstalling, uninstall it cleanly including the driver software, then install the vendor's own driver for your adapter rather than a generic one.
  6. Pair the controller fresh after each change so you are testing storage rather than an old broken key.
  7. If the pairing still does not persist, use a cheap USB Bluetooth dongle with its own driver, or use the cable, which is lower latency anyway.

Tested on: DualSense CFI-ZCT1W paired to three Bluetooth adapters on Windows 11 24H2 across ten reboots each, with fast startup on and off, with adapter power management enabled and disabled, and with generic versus vendor drivers. Fast startup with power management enabled lost the pairing on two of three adapters; both disabled retained it on all three.

Checked by Devon Miller on . How we verify answers

Did this fix your controller?
Was this answer helpful?
Share this guide

Community Replies 4

  • Accepted Solution
    Agnieszka ZielinskaCommunity Member

    Fast startup off plus the power management checkbox and the pairing has survived nine reboots in a row. Two settings, five minutes, after months of re-pairing every day.

  • Mateus BarbozaCommunity Member

    My adapter driver was reinstalling every boot, which I only noticed because the name kept changing. Vendor driver fixed it properly.

  • Harriet NgoziCommunity Member

    Four pound dongle in the end. My motherboard Bluetooth simply would not keep a key no matter what I changed.

  • Dusan MilosevicCommunity Member

    Had this on a laptop and power management was the whole problem there too. Should be the first thing anyone checks.

Add Your Reply

Add screenshots, a short recording or filesDrag here, paste a screenshot, or tap to choose. Up to 2 files, 8 MB each. JPG, JPEG, PNG, WEBP, GIF, TXT, LOG, PDF, JSON, MP4, WEBM
Liam Davies
Written and tested by

Liam DaviesVerified Gamepad Tester team member

Bluetooth And Wireless Test Engineer at Gamepad Tester

Liam works on Bluetooth Low Energy and wireless input. Most pairing complaints are not really pairing problems: they are packet drops, signal jitter or interference from a crowded 2.4GHz band, and they look completely different on a trace than they do to the player. He tests how controllers behave over distance, through walls, alongside other wireless devices, and on the proprietary dongles that several brands ship. On Gamepad Tester he answers the pairing and dropout questions and verifies fixes over both Bluetooth and adapter connections.

Bluetooth Low Energypacket loss and jitter2.4GHz interferencewireless adapterspairing faults
  • 22 answers on Gamepad Tester
  • 11+ years experience
  • Reproduces wireless dropouts and pairing faults on real hardware before a fix is published here.
  • Reviewed by Devon Miller

The Team Behind These Answers

All 40 specialists

Each answer is written by the specialist who owns that part of the hardware, tested on a real controller, and checked by a second team member. How we verify answers

Answers are free general guidance from the Gamepad Tester Team and the community. Opening a controller or replacing a thumbstick module can void your warranty, so check the maker's support or warranty first. Battery and soldering work carries a real risk of damage or injury.

Free Controller Tests

Every test runs in your own browser with the Gamepad API. No sign up, no download, and your controller data never leaves your device.

All tools

Read Next On The Gamepad Tester Blog

All articles

Latest From The Community

The newest replies from players and the Gamepad Tester Team.

All guides