Skip to main content

Gamepad Tester

AnsweredVerified By Gamepad TesterVerified By Gamepad Tester

The Greyscale Test Shows My Greys Are Slightly Blue Or Pink

Asked by Cassius T.0 views

On your greyscale test, the mid greys on my monitor have a slight blue tint, and the darker ones look a bit pink. Whites look OK. How do I make the greys neutral?

Brand
Not stated
Model
Monitor
Connection
DisplayPort
System
Windows 11
Browser
Chrome 150
Short Answer

Tinted greys mean the monitor's white balance is uneven across brightness levels. Set the colour temperature to a 6500K or standard preset, then adjust the RGB gain in the user colour settings, using mid greys in the greyscale test. Uneven tints at different levels need a colorimeter for full correction.

Verified By Gamepad TesterVerified By Gamepad Tester
Gabriel Silva
Gabriel SilvaVerified Gamepad Tester team memberGamepad Tester Team
Low Level Systems Programmer · Answered Aug 1, 2026

Greys should look neutral at every level. A blue tint in mid greys and pink in darker ones means the monitor's red, green and blue are not balanced the same way at each brightness level.

Start with the preset. In the monitor's menu, set colour temperature to 6500K, standard or sRGB, and turn off any dynamic or vivid modes. Many tints disappear with the right preset.

Then adjust the user RGB settings. Most monitors let you change red, green and blue gain. Display the mid grey steps of our greyscale test and adjust in small steps: if greys look blue, lower blue slightly or raise red and green slightly. Check other grey levels as you go.

The limitation: RGB gain mainly affects bright tones. If darker greys stay pink while mid greys look right, you need separate low-level controls, which some monitors have as offset or bias settings, or a colorimeter calibration that corrects the whole range.

Take breaks while adjusting, because your eyes adapt quickly to tints, and compare against something neutral like a white sheet of paper in daylight.

Step By Step Fix
  1. Set the monitor's colour temperature to 6500K, standard or sRGB.
  2. Turn off dynamic and vivid modes.
  3. Display mid greys in the greyscale test and adjust RGB gain in small steps.
  4. Check darker greys and use offset controls if your monitor has them.
  5. Use a colorimeter for full correction across all levels.

Tested on: Applies to LCD and OLED monitors with user colour controls. Visual adjustment guidance; full calibration requires a colorimeter.

Checked by Rebecca Wright on . How we verify answers

Did this fix your controller?
Was this answer helpful?
Share this guide

Community Replies 3

  • Accepted Solution
    Marisa KettleworthCommunity Member

    6500K preset fixed most of mine, a small red bump did the rest.

  • Cassius ThornburyCommunity Member

    Lowered blue gain two steps and the mid greys look neutral now. Dark greys still slightly pink, will get a colorimeter eventually.

  • Ajay MohanCommunity Member

    Taking breaks while adjusting really matters, my eyes kept getting used to the tint.

Add Your Reply

Add screenshots, a short recording or filesDrag here, paste a screenshot, or tap to choose. Up to 2 files, 8 MB each. JPG, JPEG, PNG, WEBP, GIF, TXT, LOG, PDF, JSON, MP4, WEBM
Gabriel Silva
Written and tested by

Gabriel SilvaVerified Gamepad Tester team member

Low Level Systems Programmer at Gamepad Tester

Gabriel is a low-level C programmer working on desktop input architecture. He builds native tooling that samples stick and trigger telemetry at sub-millisecond intervals, below the rate a browser can reach, which gives a reference measurement to compare a web test against. When a browser reading looks wrong, his capture is how the team confirms whether the controller, the operating system or the page is at fault. On Gamepad Tester he provides the reference measurements behind the latency and drift answers.

Native input capturesub-millisecond telemetrydesktop input architectureC and systems programming
  • 21 answers on Gamepad Tester
  • Captures native sub-millisecond stick and trigger data used as the reference for browser readings here.
  • Reviewed by Rebecca Wright

The Team Behind These Answers

All 40 specialists

Each answer is written by the specialist who owns that part of the hardware, tested on a real controller, and checked by a second team member. How we verify answers

Answers are free general guidance from the Gamepad Tester Team and the community. Opening a controller or replacing a thumbstick module can void your warranty, so check the maker's support or warranty first. Battery and soldering work carries a real risk of damage or injury.

Free Controller Tests

Every test runs in your own browser with the Gamepad API. No sign up, no download, and your controller data never leaves your device.

All tools

Read Next On The Gamepad Tester Blog

All articles

Latest From The Community

The newest replies from players and the Gamepad Tester Team.

All guides