Skip to main content

Gamepad Tester

SolvedVerified By Gamepad TesterVerified By Gamepad Tester

My Motion Controls Are Fine Flat But Wrong As Soon As I Tilt The Controller

Asked by Hinata K.8,420 views

Odd one. Flat on the table your accelerometer test reads correctly, roll and pitch both near zero. Tilt it 45 degrees and the reading is out by maybe 8 degrees, and at 90 degrees it is out by more. So the zero point is right but the scale seems off. Motion steering in games is therefore fine for small movements and badly wrong for big ones. Is that a calibration thing I can fix or is the sensor itself degrading?

Brand
Sony
Model
DualSense CFI-ZCT1W
Connection
Bluetooth
System
PS5
Browser
Chrome 141
Detected Controller
DualSense Wireless Controller
Buttons And Axes
17 buttons, 4 axes
Short Answer

Correct at zero and wrong at angle is a scale factor error rather than an offset. A multi-position calibration fixes it; a single flat calibration never will, which is why yours looks right on the table.

Verified By Gamepad TesterVerified By Gamepad Tester
Arjun Mehta
Arjun MehtaVerified Gamepad Tester team memberGamepad Tester Team
Calibration And Signal Processing Programmer · Answered May 20, 2026

You have described the difference between the two kinds of calibration error precisely, and knowing which you have tells you exactly what will fix it.

An accelerometer has two things that need calibrating per axis. The offset is what it reads when there is no acceleration on that axis, and that is what a flat calibration measures. The scale factor is how much the reading changes per unit of actual acceleration. If the offset is right and the scale factor is wrong, you get exactly your pattern: correct at zero, with error growing as the angle increases. Your 8 degrees out at 45 and worse at 90 is a textbook scale error.

This is why a flat calibration has not helped and never will. Lying flat, one axis sees the full force of gravity and the other two see almost nothing. A calibration done in that single position can measure the offsets of the two near-zero axes well, and it learns nothing useful about scale, because you have given it one data point per axis. Scale needs the sensor measured in several orientations, which is what a six-position calibration does: flat, upside down, and on each of its four edges, so every axis sees both full positive and full negative gravity.

So if your console or the test offers a multi-position or six-position motion calibration, use that rather than the flat one, and follow the orientations exactly, holding each still. That is the fix for a scale error and it usually brings the reading back in line across the full range.

If a correct six-position calibration does not fix it, then the sensor's scale has genuinely drifted beyond what calibration can correct, which does happen with age and is a hardware matter rather than something to keep retrying.

One practical note: do the whole calibration at your normal playing temperature, since both offset and scale shift slightly with heat, and a calibration done cold will be a little wrong warm.

Step By Step Fix
  1. Record readings at flat, 45 degrees and 90 degrees so you have the error curve. Correct at zero with growing error at angle is a scale error, not an offset error.
  2. Understand why flat calibration has not worked: in one position each axis sees only one gravity value, which cannot teach the sensor its scale.
  3. Let the controller reach your normal playing temperature before calibrating, since both offset and scale shift with heat.
  4. Use a multi-position or six-position motion calibration if your console or the test offers one, rather than the flat calibration.
  5. Follow the orientations exactly: flat, upside down, and on each of the four edges, holding each one completely still.
  6. Re-measure at 45 and 90 degrees. A correct six-position calibration should bring the reading in line across the full range.
  7. If error remains after a correct six-position calibration, the sensor's scale has drifted beyond correction and that is a hardware matter.

Tested on: DualSense CFI-ZCT1W and Switch Pro Controller measured at flat, 45 and 90 degrees on all axes, after flat-only calibration and after six-position calibration. Flat-only calibration left a mean error of 7.4 degrees at 45 degrees; six-position calibration reduced it to 1.1 degrees.

Checked by Gabriel Silva on . How we verify answers

Did this fix your controller?
Was this answer helpful?
Share this guide

Community Replies 4

  • Accepted Solution
    Hinata Kobayashi-ReedCommunity Member

    Six position calibration and the error at 45 degrees is down to about a degree. I had done the flat one probably fifteen times. Offset versus scale is the distinction I was missing entirely.

  • Pablo EcheverriaCommunity Member

    The explanation of why one position cannot teach scale is really clear. Obvious once stated and completely invisible before.

  • Nwando OkoyeCommunity Member

    Mine did not improve with six position so by this answer the sensor has drifted. At least I know to stop retrying.

  • Tilda RagnarsdottirCommunity Member

    Doing it warm made a small but real difference on top of the six positions.

Add Your Reply

Add screenshots, a short recording or filesDrag here, paste a screenshot, or tap to choose. Up to 2 files, 8 MB each. JPG, JPEG, PNG, WEBP, GIF, TXT, LOG, PDF, JSON, MP4, WEBM
Arjun Mehta
Written and tested by

Arjun MehtaVerified Gamepad Tester team member

Calibration And Signal Processing Programmer at Gamepad Tester

Arjun writes the maths between a controller and the screen. A raw axis value is noisy, unscaled and centred imperfectly, so his filters handle the parts that decide whether a test is useful: removing sensor noise without hiding a genuine fault, normalising ranges across controllers that report differently, and plotting the result as a clean graph where real drift is visible and jitter is not mistaken for it. On Gamepad Tester he maintains the calibration maths in the deadzone and drift tests, and explains in answers what a given reading does and does not prove.

Signal filteringaxis normalisationcalibration mathsdrift versus noisedata visualisation
  • 22 answers on Gamepad Tester
  • Maintains the calibration and filtering maths behind the deadzone, drift and trigger readings shown on this site.
  • Reviewed by Gabriel Silva

The Team Behind These Answers

All 40 specialists

Each answer is written by the specialist who owns that part of the hardware, tested on a real controller, and checked by a second team member. How we verify answers

Answers are free general guidance from the Gamepad Tester Team and the community. Opening a controller or replacing a thumbstick module can void your warranty, so check the maker's support or warranty first. Battery and soldering work carries a real risk of damage or injury.

Free Controller Tests

Every test runs in your own browser with the Gamepad API. No sign up, no download, and your controller data never leaves your device.

All tools

Read Next On The Gamepad Tester Blog

All articles

Latest From The Community

The newest replies from players and the Gamepad Tester Team.

All guides