Skip to main content

Gamepad Tester

AnsweredVerified By Gamepad TesterVerified By Gamepad Tester

The Colour Gamut Test Shows Saturated Reds Merging Together

Asked by Ignatius P.0 views

On your colour gamut test, the most saturated red steps all look identical, and the same happens a bit with greens. Mid steps are fine. Does that mean my monitor can't show those colours?

Brand
Not stated
Model
Monitor
Connection
HDMI
System
Windows 11
Browser
Chrome 147
Short Answer

Steps merging at the saturated end means clipping: the colours requested are beyond what the panel or current settings can show, so they collapse into the same maximum. Common causes are a limited gamut panel, vivid modes boosting saturation, or colour range settings. Use standard mode and check the range setting.

Verified By Gamepad TesterVerified By Gamepad Tester
Arjun Mehta
Arjun MehtaVerified Gamepad Tester team memberGamepad Tester Team
Calibration And Signal Processing Programmer · Answered Apr 24, 2026

When the most saturated steps look identical, those colours are being clipped. The test asks for slightly different saturated reds, but something in the chain cannot tell them apart, so they all display as the same maximum red.

There are a few common causes.

The panel's gamut. If your monitor covers less than the colour range being tested, colours beyond its reach all land at its most saturated red. Budget monitors with limited sRGB coverage do this.

Vivid or saturation settings. Picture modes that boost saturation push mid colours towards the maximum, so the top steps hit the limit early and merge. Switch to standard or sRGB mode.

Colour range or format. Limited range mismatches, or some colour format settings over HDMI, can compress the top of the range. Make sure the PC's output and the monitor agree, and try RGB full range.

After changing settings, check the test again. If mid and high steps are distinguishable in standard mode, the monitor is fine and the vivid mode was causing it. If they still merge, the panel's gamut is the limit, which is normal for monitors with smaller colour coverage and rarely matters for everyday content.

Step By Step Fix
  1. Switch the monitor to standard or sRGB mode.
  2. Turn off saturation boosts and vivid modes.
  3. Check the PC and monitor use the same colour range, and try RGB full range.
  4. Re-check the saturated steps in the colour gamut test.
  5. If they still merge, treat it as the panel's gamut limit.

Tested on: Applies to LCD and OLED monitors. Behaviour reflects how gamut limits and saturation settings affect colour steps.

Checked by Rebecca Wright on . How we verify answers

Did this fix your controller?
Was this answer helpful?
Share this guide

Community Replies 3

  • Accepted Solution
    Odalys FenwickCommunity Member

    Vivid mode was clipping my reds. Standard mode and all the steps show.

  • Ignatius PembertonCommunity Member

    Standard mode helped the greens, reds still merge at the very top. Budget panel limit then. Fine for my use.

  • Arpan GhoshCommunity Member

    Limited range mismatch did this to me over HDMI.

Add Your Reply

Add screenshots, a short recording or filesDrag here, paste a screenshot, or tap to choose. Up to 2 files, 8 MB each. JPG, JPEG, PNG, WEBP, GIF, TXT, LOG, PDF, JSON, MP4, WEBM
Arjun Mehta
Written and tested by

Arjun MehtaVerified Gamepad Tester team member

Calibration And Signal Processing Programmer at Gamepad Tester

Arjun writes the maths between a controller and the screen. A raw axis value is noisy, unscaled and centred imperfectly, so his filters handle the parts that decide whether a test is useful: removing sensor noise without hiding a genuine fault, normalising ranges across controllers that report differently, and plotting the result as a clean graph where real drift is visible and jitter is not mistaken for it. On Gamepad Tester he maintains the calibration maths in the deadzone and drift tests, and explains in answers what a given reading does and does not prove.

Signal filteringaxis normalisationcalibration mathsdrift versus noisedata visualisation
  • 22 answers on Gamepad Tester
  • Maintains the calibration and filtering maths behind the deadzone, drift and trigger readings shown on this site.
  • Reviewed by Rebecca Wright

The Team Behind These Answers

All 40 specialists

Each answer is written by the specialist who owns that part of the hardware, tested on a real controller, and checked by a second team member. How we verify answers

Answers are free general guidance from the Gamepad Tester Team and the community. Opening a controller or replacing a thumbstick module can void your warranty, so check the maker's support or warranty first. Battery and soldering work carries a real risk of damage or injury.

Free Controller Tests

Every test runs in your own browser with the Gamepad API. No sign up, no download, and your controller data never leaves your device.

All tools

Read Next On The Gamepad Tester Blog

All articles

Latest From The Community

The newest replies from players and the Gamepad Tester Team.

All guides