Skip to main content

Gamepad Tester

AnsweredVerified By Gamepad TesterVerified By Gamepad Tester

Do I Need A DAC Or Headphone Amp For My Headphones?

Asked by Theodore L.0 views

Bought nice wired headphones rated 250 ohms. On my laptop they sound quiet even at max, and the sound test is pretty low. Do I need a DAC or an amp? I don't know much about audio gear.

Brand
Not stated
Model
250 ohm wired headphones
Connection
Not Sure
System
Windows 11
Browser
Chrome 153
Short Answer

Most headphones do not need extra gear, but high-impedance models like 250 ohm ones often need more power than a laptop jack gives, which makes them quiet. A small headphone amp or a DAC with an amp gives them enough drive. If your headphones are low impedance and sound fine, you do not need one.

Verified By Gamepad TesterVerified By Gamepad Tester
Garrett Lindsay
Garrett LindsayVerified Gamepad Tester team memberGamepad Tester Team
Hardware Reviewer And Input Performance Specialist · 14+ years experience · Answered Oct 7, 2026

Short answer: for 250 ohm headphones, probably yes.

Impedance is roughly how much the headphones resist the signal. Most everyday headphones and earbuds are low impedance, around 16 to 64 ohms, and work well from laptops and phones. High-impedance headphones, often 250 ohms and up, need more voltage to reach a good volume. Laptop and phone jacks often cannot supply it, so the headphones sound quiet and sometimes thin, exactly as you describe.

A headphone amplifier supplies that extra drive. A DAC turns digital audio into the analog signal; many small USB devices combine a DAC and an amp, which also bypasses any noise from the laptop's audio circuit. For your case, a compact USB DAC and amp combination is the simple fix.

What a DAC alone does not do is magically improve already-good audio. If your headphones were low impedance and sounded fine at a comfortable volume, extra gear would add little.

When you get the amp, start at low volume. High-impedance headphones on a strong amp can get loud quickly.

Step By Step Fix
  1. Check your headphones' impedance rating.
  2. If it is high, such as 250 ohms or more, consider a USB DAC with a headphone amp.
  3. Connect it, select it as the output device in Windows, and start at low volume.
  4. Run the sound test and raise volume gradually to a comfortable level.
  5. For low-impedance headphones that already sound fine, skip extra gear.

Tested on: Applies to wired headphones on Windows 11 laptops and PCs. Guidance reflects general headphone impedance and amplification principles.

Checked by Fiona Gallagher on . How we verify answers

Did this fix your controller?
Was this answer helpful?
Share this guide

Community Replies 3

  • Accepted Solution
    Leopold MarshCommunity Member

    Small USB DAC/amp with my 300 ohm headphones transformed them. Laptop jack just couldn't drive them.

  • Theodore LinsellCommunity Member

    Got a compact DAC/amp. Loud and full now, and the sound test is at a comfortable level at half volume.

  • Kunal SaxenaCommunity Member

    My 32 ohm headphones sounded the same with or without a DAC. Depends on the headphones.

Add Your Reply

Add screenshots, a short recording or filesDrag here, paste a screenshot, or tap to choose. Up to 2 files, 8 MB each. JPG, JPEG, PNG, WEBP, GIF, TXT, LOG, PDF, JSON, MP4, WEBM
Garrett Lindsay
Written and tested by

Garrett LindsayVerified Gamepad Tester team member

Hardware Reviewer And Input Performance Specialist at Gamepad Tester

Garrett reviews gaming controllers the slow way. Instead of a week of impressions he runs a fixed battery of measurements on every pad: resting deadzone on both sticks, raw polling rate over wired and wireless, trigger travel consistency, and how the face buttons and stick modules hold up over extended use. The result is a review that can be checked rather than argued with, which is why his numbers are cited in the buying guides here. On Gamepad Tester he leads the reviews and buying topic, and signs off answers that recommend one controller over another.

Controller reviewspolling rate measurementdeadzone benchmarkingcomponent lifetimebuying advice
  • 20 answers on Gamepad Tester
  • 14+ years experience
  • Runs a fixed, metrics-driven review process on every controller covered in the buying guides on this site.
  • Reviewed by Fiona Gallagher

The Team Behind These Answers

All 40 specialists

Each answer is written by the specialist who owns that part of the hardware, tested on a real controller, and checked by a second team member. How we verify answers

Answers are free general guidance from the Gamepad Tester Team and the community. Opening a controller or replacing a thumbstick module can void your warranty, so check the maker's support or warranty first. Battery and soldering work carries a real risk of damage or injury.

Free Controller Tests

Every test runs in your own browser with the Gamepad API. No sign up, no download, and your controller data never leaves your device.

All tools

Read Next On The Gamepad Tester Blog

All articles

Latest From The Community

The newest replies from players and the Gamepad Tester Team.

All guides