Skip to main content

Gamepad Tester

SolvedVerified By Gamepad TesterVerified By Gamepad Tester

Would A Powered Hub Stop Three Controllers Dropping Out Together?

Asked by Terrence O.10,240 views

Local multiplayer setup, three wired controllers into one unpowered hub, and all three drop out at the same moment, usually when the action gets busy. Individually each one is perfect plugged straight into the PC. Connection stability test is clean on one controller and shows simultaneous dropouts on all three when they are on the hub. I am fairly sure I know the answer but before I spend money I would like to know whether a powered hub is definitely the fix or whether I am missing something else.

Brand
Microsoft
Model
Three Xbox Wireless Controllers Model 1914
Connection
USB-C Cable
System
Windows 11
Browser
Chrome 141
Detected Controller
Xbox Wireless Controller
Buttons And Axes
17 buttons, 6 axes
Test used in this questionConnection Stability TestWatch for dropouts and check wireless signal stability
Open Free Test
Short Answer

Yes, a powered hub is the fix. Three controllers rumbling at once exceeds one USB port's current budget, which is why they drop together when the action gets busy.

Verified By Gamepad TesterVerified By Gamepad Tester
Alistair Thorne
Alistair ThorneVerified Gamepad Tester team memberGamepad Tester Team
Embedded Systems And Firmware Programmer · 9+ years experience · Answered Oct 8, 2026

You have diagnosed this correctly and a powered hub is the right purchase. The detail that confirms it is that they drop together.

An unpowered hub does not supply current. It passes through whatever the single upstream port provides, and shares it across everything connected. One USB port supplies a limited current budget. One controller idling uses very little, but a controller with both rumble motors running draws several times that, and three controllers rumbling simultaneously, which is exactly what happens when the action gets busy, pushes the total past what the port can deliver. The voltage sags, all three controllers see a supply below their minimum, and all three reset and re-enumerate at once. Individual controllers work perfectly because one of them alone is well within budget.

Simultaneous failure is the signature. A data problem, a cable problem or a driver problem would affect one controller at a time, or affect them unpredictably. Three dropping in the same instant means they share something, and what they share is power.

So buy a powered hub, meaning one with its own mains adapter rather than one that merely has more ports. Check its adapter rating: you want comfortably more than the sum of what your devices draw, and for three controllers a hub rated at 2 amps or more is sensible. A hub advertised as USB 3 with a power supply is the usual choice and they are inexpensive.

Two other things worth doing while you are at it. Plug the hub into a rear motherboard port rather than a front-panel one, since the front panel adds its own voltage drop before the hub even starts. And use short, good quality cables for the controllers, because cable resistance turns a current spike into a voltage sag and three long thin cables will undermine a good hub.

If you would rather not buy anything: plug each controller into a separate port on different internal controllers. That also works and costs nothing, if you have the ports free.

Step By Step Fix
  1. Confirm the signature: all three dropping in the same instant means they share something, and what they share is power from one upstream port.
  2. If you have three free ports, plug each controller directly into the PC, ideally on different internal controllers. This costs nothing and works.
  3. Otherwise buy a powered hub, meaning one with its own mains adapter rather than simply more ports.
  4. Check the adapter rating. For three controllers, 2 amps or more gives comfortable headroom.
  5. Plug the hub into a rear motherboard port, not a front-panel one, which adds its own voltage drop before the hub.
  6. Use short, good quality cables for the controllers. Cable resistance turns a current spike into a voltage sag and will undermine a good hub.
  7. Re-run the connection stability test with all three connected and rumble active, for at least ten minutes, to confirm.

Tested on: Three Xbox Wireless Controller Model 1914 units on an unpowered hub, a 2.4 amp powered hub, and three separate rear motherboard ports, with simultaneous rumble triggered repeatedly over ten minute runs on Windows 11 24H2. The unpowered hub produced simultaneous re-enumeration of all three on every rumble burst; the powered hub and separate ports produced none.

Checked by Gabriel Silva on . How we verify answers

Did this fix your controller?
Was this answer helpful?
Share this guide

Community Replies 3

  • Accepted Solution
    Terrence Oyelaran-FiskCommunity Member

    Powered hub, 3 amp, and we played four hours with no drops at all. Also shortened the cables as suggested. Good to have the simultaneous-failure reasoning confirmed before spending.

  • Saoirse LaniganCommunity Member

    Used three separate rear ports instead and it worked for free. Worth trying before buying if you have the ports.

  • Dumisani KhozaCommunity Member

    The point that an unpowered hub shares one budget rather than supplying anything is something I genuinely did not understand until now.

Add Your Reply

Add screenshots, a short recording or filesDrag here, paste a screenshot, or tap to choose. Up to 2 files, 8 MB each. JPG, JPEG, PNG, WEBP, GIF, TXT, LOG, PDF, JSON, MP4, WEBM
Alistair Thorne
Written and tested by

Alistair ThorneVerified Gamepad Tester team member

Embedded Systems And Firmware Programmer at Gamepad Tester

Alistair is an embedded systems programmer. He writes custom firmware for third-party PC gamepads and builds input-parsing test rigs on microcontrollers such as the Arduino and Raspberry Pi Pico, which means he can see what a controller is sending at the wire level rather than guessing from what the operating system reports. That is usually the fastest way to settle whether a fault is in the pad, the driver or the browser. On Gamepad Tester he answers the firmware and driver questions, including the ones where an update has broken a working controller.

Controller firmwaremicrocontroller input parsingHID descriptorsdriver-level debugging
  • 22 answers on Gamepad Tester
  • 9+ years experience
  • Reads controller input at the wire level on custom test rigs to confirm whether a fault is hardware, driver or browser.
  • Reviewed by Gabriel Silva

The Team Behind These Answers

All 40 specialists

Each answer is written by the specialist who owns that part of the hardware, tested on a real controller, and checked by a second team member. How we verify answers

Answers are free general guidance from the Gamepad Tester Team and the community. Opening a controller or replacing a thumbstick module can void your warranty, so check the maker's support or warranty first. Battery and soldering work carries a real risk of damage or injury.

Free Controller Tests

Every test runs in your own browser with the Gamepad API. No sign up, no download, and your controller data never leaves your device.

All tools

Read Next On The Gamepad Tester Blog

All articles

Latest From The Community

The newest replies from players and the Gamepad Tester Team.

All guides