Skip to main content

Gamepad Tester

AnsweredVerified By Gamepad TesterVerified By Gamepad Tester

My Stick Only Reaches About 0.85 At The Edge, Never Full 1.00

Asked by Natalie O.0 views

On your joystick range test my right stick only reaches about 0.85 when I push it all the way in some directions, especially up and left. Other directions reach 1.00. In games turning feels slower in those directions. Is that wear, and can I fix it?

Brand
Sony
Model
DualSense CFI-ZCT1W
Connection
USB-C Cable
System
Windows 11
Browser
Chrome 151
Detected Controller
DualSense Wireless Controller
Buttons And Axes
17 buttons, 4 axes
Test used in this questionJoystick Deadzone TestMeasure and calibrate the deadzone on both analog sticks
Open Free Test
Short Answer

A stick that stops short in some directions usually has a calibration offset or wear at the end of its track. On a DualSense, range calibration with the DualShock Calibration GUI often restores full travel. Check for anything physically blocking the stick first.

Verified By Gamepad TesterVerified By Gamepad Tester
Elena Rostova
Elena RostovaVerified Gamepad Tester team memberGamepad Tester Team
Hardware Diagnostics Engineer · 7+ years experience · Answered Aug 11, 2026

Reaching full value in some directions but only 0.85 in others is a range problem, not a centre problem, and it is often fixable.

There are three common causes. The first is calibration. The controller stores where each axis ends; if that has shifted, some directions top out early. The second is wear or dirt at the far end of the potentiometer track, which can stop a direction short of full. The third is physical: a stick cap, grip or a slightly misaligned shell can stop the stick before it reaches its true edge.

Check the physical side first. Remove any stick extenders or thumb grips and test again. Push gently to the edge and feel whether something stops it early.

On a DualSense, the DualShock Calibration GUI includes range calibration as well as centre calibration. Run centre first, then range, rotating the stick slowly as instructed, and save permanently only when our range test shows every direction reaching close to 1.00.

If the shortfall remains after calibrating, the track is worn at that end, and a stick module replacement is the fix. Many games also map about 0.9 and above to full speed, so a small shortfall can matter less than the number suggests.

Step By Step Fix
  1. Remove stick extenders or grips and run the range view of the joystick deadzone test again.
  2. Rotate the stick slowly around its edge and note which directions stop short.
  3. Update the controller firmware, then run Calibrate stick center followed by Calibrate stick range in the DualShock Calibration GUI.
  4. Save permanently only when every direction reaches close to 1.00 in our range test.
  5. If the shortfall remains, clean the stick or plan a module replacement.

Tested on: Applies to DualSense CFI-ZCT1W on Windows 11 with Chrome or Edge over USB-C. Range calibration per the DualShock Calibration GUI project.

Checked by Arjun Mehta on . How we verify answers

Did this fix your controller?
Was this answer helpful?
Share this guide

Community Replies 3

  • Accepted Solution
    Felicity MooreCommunity Member

    My thumb grips were stopping the stick early. Took them off and it hits 1.00 everywhere.

  • Natalie OkoroCommunity Member

    No grips on mine. Range calibration got me to 0.98 in all directions. Turning feels even again.

  • Zubair AhmedCommunity Member

    Range calibration is underrated. Mine was stuck at 0.9 diagonally before.

Add Your Reply

Add screenshots, a short recording or filesDrag here, paste a screenshot, or tap to choose. Up to 2 files, 8 MB each. JPG, JPEG, PNG, WEBP, GIF, TXT, LOG, PDF, JSON, MP4, WEBM
Elena Rostova
Written and tested by

Elena RostovaVerified Gamepad Tester team member

Hardware Diagnostics Engineer at Gamepad Tester

Elena is a hardware diagnostics engineer working on competitive gaming peripherals. She designs test benches that put a number on the faults players usually describe by feel: outer deadzone error, circularity variance, uneven travel between the left and right stick, and the drift that appears only after a pad has warmed up. Her work covers custom and pro-tier hardware such as the Xbox Elite range and SCUF-style builds, where small geometry errors decide whether a shot lands. On Gamepad Tester she writes and checks the answers about deadzone readings and stick accuracy, and confirms a fix on real hardware before it is published.

Outer deadzone errorstick circularitycontroller test benchespro and custom controllersmechanical tolerance
  • 16 answers on Gamepad Tester
  • 7+ years experience
  • Designs and runs the bench tests used to verify deadzone and stick accuracy answers on this site.
  • Reviewed by Arjun Mehta

The Team Behind These Answers

All 40 specialists

Each answer is written by the specialist who owns that part of the hardware, tested on a real controller, and checked by a second team member. How we verify answers

Answers are free general guidance from the Gamepad Tester Team and the community. Opening a controller or replacing a thumbstick module can void your warranty, so check the maker's support or warranty first. Battery and soldering work carries a real risk of damage or injury.

Free Controller Tests

Every test runs in your own browser with the Gamepad API. No sign up, no download, and your controller data never leaves your device.

All tools

Read Next On The Gamepad Tester Blog

All articles

Latest From The Community

The newest replies from players and the Gamepad Tester Team.

All guides