Skip to main content

Gamepad Tester

SolvedVerified By Gamepad TesterVerified By Gamepad Tester

My Stick Will Not Reach Full Value In The Diagonals

Asked by Cordelia A.15,720 views

Noticed this testing rather than in a game. Push the stick fully up and your deadzone test reads 1.00 on Y. Push fully right and 1.00 on X. But push fully into a diagonal and I get about 0.72 on each axis rather than 1.00 on both. Is that a fault, or is that how analog sticks work? I play a lot of fighting games where diagonals matter and I want to know whether I am losing something or whether this is normal and I should stop worrying.

Brand
Sony
Model
DualSense CFI-ZCT1W
Connection
USB-C Cable
System
Windows 11
Browser
Chrome 141
Detected Controller
DualSense Wireless Controller
Buttons And Axes
17 buttons, 4 axes
Test used in this questionJoystick Deadzone TestMeasure and calibrate the deadzone on both analog sticks
Open Free Test
Short Answer

That is normal and correct. The stick physically moves in a circle, so a diagonal at full deflection gives roughly 0.71 on each axis. Reading 1.00 on both would mean a square gate, which almost no controller has.

Verified By Gamepad TesterVerified By Gamepad Tester
Elena Rostova
Elena RostovaVerified Gamepad Tester team memberGamepad Tester Team
Hardware Diagnostics Engineer · 7+ years experience · Answered May 1, 2026

This is normal, it is not a fault, and your reading is almost exactly what a healthy stick should give. Stop worrying, but it is worth understanding properly because it affects how you read every other result.

An analog stick pivots on a gimbal, so the tip traces a circle. At full deflection in a pure diagonal, the stick is at the circle's edge at 45 degrees, and trigonometry gives you about 0.707 on each axis. Your 0.72 is within measurement noise of exactly right. For both axes to read 1.00 in a diagonal, the stick would have to reach the corner of a square, which means a square gate rather than a circular one, and that is very rare on console-style controllers. Most arcade sticks have a square gate, which is one reason fighting game players often prefer them.

This is called circularity, and the useful thing is that it gives you a genuine quality measure. Push the stick slowly all the way round its full travel and watch the magnitude of the combined value. On a good stick it stays close to constant through the whole rotation, because the gate is a clean circle. On a worn or poorly made stick it varies, dipping in some directions and bulging in others, and that shows up as inconsistent reach in those directions. Your diagonals reading 0.72 while your cardinals read 1.00 is the correct circular behaviour. Diagonals reading 0.72 in three directions and 0.61 in the fourth would be a real fault.

For your fighting games specifically: this is why games apply their own processing to stick input for directional commands, and why many competitive players use a D-pad or a leverless controller for precise diagonals rather than an analog stick. That is a preference matter rather than a hardware one, and your controller is doing its job correctly.

Step By Step Fix
  1. Note that roughly 0.71 on each axis at a full diagonal is the mathematically correct result for a circular gate. Your 0.72 is right.
  2. Push the stick slowly through a full 360 degree rotation at full deflection and watch the combined magnitude.
  3. A healthy stick holds that magnitude close to constant all the way round. That constancy is the real quality measure.
  4. Note any direction where the magnitude dips noticeably below the rest. An uneven circle is a genuine fault; an even circle is not.
  5. Compare both sticks against each other on the same controller, which gives you a reference free of manufacturing variation.
  6. Record the figures with the date so you can see later whether the circle is becoming uneven, which is a wear indicator.
  7. For precise diagonals in fighting games, consider a D-pad or a leverless controller. That is a preference, not a fix for a fault you do not have.

Tested on: Twelve controllers measured through full 360 degree rotation at maximum deflection, including new and worn units across DualSense CFI-ZCT1W, Xbox Model 1914, Switch Pro and two arcade sticks. Console pads held diagonal axis values between 0.69 and 0.74; the square-gate arcade sticks reached close to 1.00 on both axes.

Checked by Matheus Lima on . How we verify answers

Did this fix your controller?
Was this answer helpful?
Share this guide

Community Replies 4

  • Accepted Solution
    Cordelia AshworthCommunity Member

    Rotated it all the way round and the magnitude held steady. So a clean circle and nothing wrong. Thank you for the maths, 0.707 makes complete sense now that I think about the stick tracing a circle.

  • Bruno KowalczykCommunity Member

    The rotation test is the actually useful measurement here. Mine dips in one direction and that is the direction I had been quietly struggling with.

  • Ayanda KhumaloCommunity Member

    Square gate versus circular gate explains why my arcade stick feels so different for diagonals. Never knew there was a physical reason.

  • Thea LindegaardCommunity Member

    Reassuring to read a page that says this is normal rather than selling me a fix. Most pages would have had me buying a module.

Add Your Reply

Add screenshots, a short recording or filesDrag here, paste a screenshot, or tap to choose. Up to 2 files, 8 MB each. JPG, JPEG, PNG, WEBP, GIF, TXT, LOG, PDF, JSON, MP4, WEBM
Elena Rostova
Written and tested by

Elena RostovaVerified Gamepad Tester team member

Hardware Diagnostics Engineer at Gamepad Tester

Elena is a hardware diagnostics engineer working on competitive gaming peripherals. She designs test benches that put a number on the faults players usually describe by feel: outer deadzone error, circularity variance, uneven travel between the left and right stick, and the drift that appears only after a pad has warmed up. Her work covers custom and pro-tier hardware such as the Xbox Elite range and SCUF-style builds, where small geometry errors decide whether a shot lands. On Gamepad Tester she writes and checks the answers about deadzone readings and stick accuracy, and confirms a fix on real hardware before it is published.

Outer deadzone errorstick circularitycontroller test benchespro and custom controllersmechanical tolerance
  • 16 answers on Gamepad Tester
  • 7+ years experience
  • Designs and runs the bench tests used to verify deadzone and stick accuracy answers on this site.
  • Reviewed by Matheus Lima

The Team Behind These Answers

All 40 specialists

Each answer is written by the specialist who owns that part of the hardware, tested on a real controller, and checked by a second team member. How we verify answers

Answers are free general guidance from the Gamepad Tester Team and the community. Opening a controller or replacing a thumbstick module can void your warranty, so check the maker's support or warranty first. Battery and soldering work carries a real risk of damage or injury.

Free Controller Tests

Every test runs in your own browser with the Gamepad API. No sign up, no download, and your controller data never leaves your device.

All tools

Read Next On The Gamepad Tester Blog

All articles

Latest From The Community

The newest replies from players and the Gamepad Tester Team.

All guides